Drive It Like You Stole It

April 27, 2013

Drive It Like You Stole It

Officer, it’s not what it looks like! I did not steal this car; that’s my key! Why are you getting out your taser?!

For no practical purpose at all, I wanted to see if I could make a screwdriver into a car key. What fun it would be to impersonate the look of a stolen car with a screwdriver jammed into the ignition! And maybe I could empty my glove box all over the seat so it looks like I was scrounging for spare change and prescription drugs too!

Read on to make your own.

 

Hit the thrift store or a nearby garage sale and get a beat up old screwdriver with a shaft about the same thickness as the width of your car key. Don’t get a new screwdriver; you want one with some character, one that looks like it might have stabbed someone. Cut the shaft down to about an inch long.

Cut a slot 1/4″ – 3/8″ deep in the end of the shaft. This is not a precision job.

Round the end on a grinder or with a file. This will give a nice, smooth transition between the key and the screwdriver shaft.

Take your car key out to the car, put it in the ignition, and mark how far in it needs to go to start the car. Add the depth of the slot you cut in the shaft to that mark, then cut. Oh, and use a spare key for this. Not your one-and-only original.

The key needs to fit into the slot you cut in the screwdriver, so unless you gut a lucky match between your key and your kerf you can either widen the slot or narrow the key. I chose the latter and thinned it on a belt sander. Don’t take off to much because you want the key to fit tightly.

Put some flux on it the key, then tap it into the slot on the screwdriver shaft. Be sure that everything is lined up. With a torch, silver solder the key to the screwdriver.

With a file or grinder, taper the edges of the key to meet the screwdriver shaft. Smooth it with some sandpaper and clean it with a wire wheel in a Dremel.

All done! Now cruise around like the grand theft auto thug you are!

If you make your own, take a picture and email it to me (nathan@ the domain name of this site) and I’ll share it here if you’re willing. Bonus points if the picture includes police in the background ordering you out of your car!

NOTE:  Having this much weight and leverage hanging out of your ignition is not going to be good for it. One bump and your tumblers are toast. It also won’t work if you’ve got a modern car with a chip in the key. Consider yourself warned.

[May 6, 2013] HaHaBird reader Richie emailed pictures of the screwdriver key he made. Nice work!

 

Leave a comment

Comments will be approved before showing up.


Also in Projects

The Laboratory Lamp
The Laboratory Lamp

February 17, 2016

First created in 1860, the Erlenmeyer flask has come to symbolize chemistry, and by extension science as a whole. I wanted to use that symbol to create an item of functional decor, and what better for that than a lamp, with the relationship between the light bulb and the “aha!” of an idea?

 

View full article →

Garbage In, Garbage Out
Garbage In, Garbage Out

February 04, 2016

For over a decade I’ve had kicking around in my garage’s attic the cases from a couple of old original-style Macintoshes, waiting for just the right project.

One day, after staring at them stacked in my office, I realized that they had a similar form factor to the classic bullet-top garbage cans with the swinging lid. I could give one of these a new (slightly unceremonious) life as a garbage can!

View full article →

Moon Phase Purse
Moon Phase Purse

January 20, 2015

I’ve been going through a moon phase recently (pun absolutely intended), and thought it would be fun to make a wearable or totable that displayed the current state of the moon. There would be a bit of hardware involved, so a purse seemed like the perfect vehicle—you’re already carrying a load of other things, so there’s no harm in the addition of a small battery pack or a pile of LEDs.

 

View full article →